实际上，现在发行的许多Internet应用软件中已包含了安全特征。例如，Netscape Navigator和Microsoft Internet Explorer支持保护互联网通信的安全套层协议（SSL），还有一部分产品支持保护Internet上信用卡交易的安全电子交易协议（SET）。然 而，×××需要的是网络级的功能，这也正是IPSec所提供的。
[root@bogon ipsec.d]# ipsec verify
Verifying installed system and configuration files
Version check and ipsec on-path [OK]
Libreswan 3.15 (netkey) on 3.10.0-514.10.2.el7.x86_64
Checking for IPsec support in kernel [OK]
NETKEY: Testing XFRM related proc values
ICMP default/send_redirects [OK]
ICMP default/accept_redirects [OK]
XFRM larval drop [OK]
Pluto ipsec.conf syntax [OK]
Hardware random device [N/A]
Two or more interfaces found, checking IP forwarding [OK]
Checking rp_filter [ENABLED]
/proc/sys/net/ipv4/conf/eth0/rp_filter [ENABLED]
rp_filter is not fully aware of IPsec and should be disabled
Checking that pluto is running [OK]
Pluto listening for IKE on udp 500 [OK]
Pluto listening for IKE/NAT-T on udp 4500 [OK]
Pluto ipsec.secret syntax [OK]
Checking 'ip' command [OK]
Checking 'iptables' command [OK]
Checking 'prelink' command does not interfere with FIPSChecking for obsolete ipsec.conf options [OK]
Opportunistic Encryption [DISABLED]
ipsec verify: encountered 3 errors - see 'man ipsec_verify' for help
[root@bogon ipsec.d]# echo 0 >/proc/sys/net/ipv4/conf/eth0/rp_filter #解决办法
[root@bogon ipsec.d]# ipsec verify
Verifying installed system and configuration files
Version check and ipsec on-path [OK]
Libreswan 3.15 (netkey) on 3.10.0-514.10.2.el7.x86_64
Checking for IPsec support in kernel [OK]
NETKEY: Testing XFRM related proc values
ICMP default/send_redirects [OK]
ICMP default/accept_redirects [OK]
XFRM larval drop [OK]
Pluto ipsec.conf syntax [OK]
Hardware random device [N/A]
Two or more interfaces found, checking IP forwarding [OK]
Checking rp_filter [OK]
Checking that pluto is running [OK]
Pluto listening for IKE on udp 500 [OK]
Pluto listening for IKE/NAT-T on udp 4500 [OK]
Pluto ipsec.secret syntax [OK]
Checking 'ip' command [OK]
Checking 'iptables' command [OK]
Checking 'prelink' command does not interfere with FIPSChecking for obsolete ipsec.conf options [OK]
Opportunistic Encryption [DISABLED]
[root@bogon ipsec.d]#
8.启动服务
systemctl start ipsec
systemctl enable ipsec
9.安装配置xl2tpd服务
yum install xl2tpd
vi /etc/xl2tpd/xl2tpd.conf #修改l2tp的配置文件
[root@bogon xl2tpd]# cat xl2tpd.conf
;
; This is a minimal sample xl2tpd configuration file for use
; with L2TP over IPsec.
;
; The idea is to provide an L2TP daemon to which remote Windows L2TP/IPsec
; clients connect. In this example, the internal (protected) network
; is 192.168.1.0/24. A special IP range within this network is reserved
; for the remote clients: 192.168.1.128/25
; (i.e. 192.168.1.128 ... 192.168.1.254)
;
; The listen-addr parameter can be used if you want to bind the L2TP daemon
; to a specific IP address instead of to all interfaces. For instance,
; you could bind it to the interface of the internal LAN (e.g. 192.168.1.98
; in the example below). Yet another IP address (local ip, e.g. 192.168.1.99)
; will be used by xl2tpd as its address on pppX interfaces.
[global]
ipsec saref = yes #此处添加上去
listen-addr = 192.168.56.11 #外网
;
; requires openswan-2.5.18 or higher - Also does not yet work in combination
; with kernel mode l2tp as present in linux 2.6.23+
; ipsec saref = yes
; Use refinfo of 22 if using an SAref kernel patch based on openswan 2.6.35 or
; when using any of the SAref kernel patches for kernels up to 2.6.35.
; saref refinfo = 30
;
; force userspace = yes
;
; debug tunnel = yes
[lns default]
ip range = 10.0.0.100-10.0.0.200 #要和自己的内网一直 分配给客户端的IP地址
local ip = 192.168.56.11
require chap = yes
refuse pap = yes
require authentication = yes
name = Linux×××server
ppp debug = yes
pppoptfile = /etc/ppp/options.xl2tpd
length bit = yes
10.修改xl2tpd属性配置文件
vi /etc/ppp/options.xl2tpd
[root@bogon xl2tpd]# cat /etc/ppp/options.xl2tpd
ipcp-accept-local
ipcp-accept-remote
ms-dns 8.8.8.8 #只修改DNS 建议改成网关的IP
# ms-dns 192.168.1.1
# ms-dns 192.168.1.3
# ms-wins 192.168.1.2
# ms-wins 192.168.1.4
noccp
auth
crtscts
idle 1800
mtu 1410
mru 1410
nodefaultroute
debug
lock
proxyarp
connect-delay 5000
# To allow authentication against a Windows domain EXAMPLE, and require the
# user to be in a group "××× Users". Requires the samba-winbind package
require-mschap-v2
# plugin winbind.so
# ntlm_auth-helper '/usr/bin/ntlm_auth --helper-protocol=ntlm-server-1 --require-membership-of="EXAMPLE\\××× Users"'
# You need to join the domain on the server, for example using samba:
# http://rootmanager.com/ubuntu-ipsec-l2tp-windows-domain-auth/setting-up-openswan-xl2tpd-with-native-windows-clients-lucid.html
[root@bogon xl2tpd]#
11.添加用户名密码
[root@bogon xl2tpd]# cat /etc/ppp/chap-secrets
# Secrets for authentication using CHAP
# client server secret IP addresses
***12345 * 123456 *
[root@bogon xl2tpd]#
12.启动l2tp服务
systemctl start xl2tpd
systemctl enable xl2tpd
systemctl status xl2tpd
